Vector VEC139 Especificaciones Pagina 182
- Pagina / 268
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
CHAPTER 10: POWER ANALYSIS
PERFORMING POWER ANALYSIS WITH THE POWERPLAY POWER ANALYZER
ALTERA CORPORATION INTRODUCTION TO QUARTUS II ■ 175
probabilities using user assignments in Quartus II user interface or in the
Quartus II Settings File (.qsf). For some device families, the Quartus II
software will fill in any missing signal activity information by analyzing the
design topology and function.
You can then start power analysis by clicking Start in the Power Analyzer
Tool window
— a status bar shows the processing time. When power
analysis is complete, you can click Report to display the Report File (.rpt,
.htm). See Figure 2.
Figure 2. PowerPlay Power Analyzer Tool
The Start button starts
power analysis
The progress bar shows
the elapsed time spent
processing the design
The Report button displays
the Power Analysis section
of the Report File.
- Introduction to 1
- Contents 3
- TABLE OF CONTENTS 4
- Documentation Conventions 9
- Terminology 10
- Design Flow 11
- Introduction 12
- CHAPTER 1: DESIGN FLOW 13
- Quartus II Help 16
- EDA Tool Design Flow 20
- EDA TOOL DESIGN FLOW 21
- HAPTER 1: DESIGN FLOW 22
- OOL DESIGN FLOW 22
- Command-Line Design Flow 26
- Command-Line Executables 27
- OMMAND-LINE DESIGN FLOW 28
- COMMAND-LINE DESIGN FLOW 30
- Using Standard Command-Line 33
- Commands & Scripts 33
- Using Tcl Commands 34
- Creating Makefile Scripts 37
- Planning 40
- Design Entry 43
- Creating a Project 45
- CHAPTER 2: DESIGN ENTRY 46
- CREATING A PROJECT 46
- Using Revisions 47
- Creating a Design 53
- CREATING A DESIGN 54
- Using Altera Megafunctions 57
- Megafunctions 58
- Using the MegaWizard Plug-In 59
- Inferring Megafunctions 61
- USING ALTERA MEGAFUNCTIONS 62
- Instantiation by Inference 63
- Constraint Entry 65
- Using the Assignment Editor 67
- CHAPTER 3: CONSTRAINT ENTRY 68
- USING THE ASSIGNMENT EDITOR 68
- Using the Pin Planner 69
- Using the Settings Dialog Box 70
- USING THE SETTINGS DIALOG BOX 71
- Assigning Design Partitions 72
- Design Partitions Window 73
- Importing Assignments 74
- Verifying Pin Assignments 75
- VERIFYING PIN ASSIGNMENTS 76
- Synthesis 77
- VHDL Integrated Synthesis 79
- CHAPTER 4: SYNTHESIS 80
- HAPTER 4: SYNTHESIS 83
- Attributes 85
- Optimization Options 88
- Place & Route 98
- CHAPTER 5: PLACE & ROUTE 100
- INTRODUCTION 100
- Compilation 101
- Analyzing Fitting Results 102
- ANALYZING FITTING RESULTS 103
- File to View Fitting Results 104
- Analyze Results 105
- Design Reliability 107
- Optimizing the Fit 108
- Setting Fitter Options 109
- OPTIMIZING THE FIT 110
- Back-Annotation 118
- Block-Based Design 121
- CHAPTER 6: BLOCK-BASED DESIGN 123
- Using LogicLock Regions 124
- USING LOGICLOCK REGIONS 125
- Down Incremental Compilation 127
- Assignments 130
- Simulation 134
- The ModelSim-Altera Software 136
- design 136
- Settings 137
- CHAPTER 7: SIMULATION 138
- EDA Simulation Flow 139
- NativeLink Simulation Flow 140
- Manual Timing Simulation Flow 140
- Simulation Libraries 141
- HAPTER 7: SIMULATION 142
- Simulating Designs with the 143
- Quartus II Simulator 143
- Creating Waveform Files 145
- Using the Simulator Tool 146
- Timing Analysis 148
- Quartus II Software 150
- CHAPTER 8: TIMING ANALYSIS 151
- Performing a Timing Analysis 155
- Performing an Early Timing 157
- Estimate 157
- Using the Report Window 159
- Using EDA Tools 164
- Using the PrimeTime Software 166
- Using the Tau Software 167
- Timing Closure 168
- CHAPTER 9: TIMING CLOSURE 170
- Making Assignments 172
- Achieve Timing Closure 174
- Soft LogicLock Regions 177
- Path-Based Assignments 177
- Figure 5. Paths Dialog Box 178
- Power Analysis 180
- PowerPlay Power Analyzer 181
- CHAPTER 10: POWER ANALYSIS 182
- Estimator 185
- HAPTER 10: POWER ANALYSIS 186
- Programming & 187
- Configuration 187
- Converting Programming Files 196
- Debugging 201
- Using the SignalTap II Logic 203
- Analyzer 203
- Logic Analyzer 204
- CHAPTER 12: DEBUGGING 205
- Analyzing SignalTap II Data 209
- Using SignalProbe 211
- USING SIGNALPROBE 212
- Using the In-System Memory 214
- Content Editor 214
- Map Viewer 216
- Using the Chip Editor 217
- Thirteen 218
- Fourteen 227
- PECIFYING ADDITIONAL SETTINGS 231
- System-Level Design 233
- Creating SOPC Designs with 236
- SOPC Builder 236
- Generating the System 237
- DSP Builder 238
- Instantiating Functions 239
- Generating Simulation Files 239
- Generating Synthesis Files 239
- Software Development 241
- MegaWizard Plug-In 245
- Quartus II 245
- Software Builder 245
- ■ Raw Binary Files (.rbf) 246
- ■ SRAM Object Files (.sof) 246
- ■ Tabular Text Files (.ttf) 246
- Seventeen 250
- ■ Mentor Graphics 252
- ■ Altera Quartus II software 252
- Getting Technical Support 254
- Altera.com account 255
- Eighteen 256
- Getting Online Help 257
- Other Quartus II Software 259
- Documentation 259
- Other Altera Literature 260
- OTHER ALTERA LITERATURE 261
Relacionado con productos y manuales para Luces de trabajo Vector VEC139
(6 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.073 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales